Hawking Technology HWU54D User Manual

C. Click “Continue Anyway” to finish the installation. II. Install the USB Adapter A. Plug the USB Adapter into the USB port of your computer.

C. Click “Continue Anyway” and the system will start to install the USB adapter. 11

D. Click “Finish” to complete the installation. III. Using the Configuration Utility To setup the USB adapter, double-click the icon in the system

3 Configuration Utility The Configuration Utility is a powerful application that helps you configure the Hawking Technologies 802.11g Wireless LAN Hi

Parameter Description Mode Station – Set the USB adapter as a wireless client. Access Point – Allows the USB adapter to function as a wireless

BSSID Display the MAC Address of the network the adapter is connecting to. Parameter Description Signal Strength This bar shows the signal stren

General Connection Setting Channel Selects the radio channel to be used for wireless networking. The channel setting of the wireless stations with

Parameter Description Authentication Mode This setting must be consistent with the wireless networks that the adapter intends to connect with.

1.6 WEP and WPA Encryption WEP is a data encryption algorithm, which protects Wireless networks from outside intruders or “eavesdropping.” T

Parameter Description Key1 ~ Key4 The keys are used to encrypt data transmitted in the wireless network. Fill the text box by following the r

LIMITED WARRANTY Hawking Technology guarantees that every HWU54D Hi-Gain Wireless-G USB Network Adapter is free from physical defects in material a

Parameter Description Connect Information It is the setting for WPA mode. Protocol This adapter supports two kind of protocol

Pre-shared Key It is the setting for WPA-PSK mode. Input a key that is 8 to 63 digits in length using ASCII format as the password for the authentic

enabled: English and Chinese. Country Roaming IEEE 802.11d (Country Roaming) is a standard that enable the wireless devices work at the proper tra

1.8 Software AP Mode The HWU54D Hi-Gain USB Wireless-G adapter has a unique feature that allows it to function as a Wireless Access Point. By chan

the AP successfully. RX Frame It shows the number of data frames which are received by the AP successfully. 3.1.4 AP General Connection Sett

Parameter Description Tx Rate There are several options including Auto/1/2/5.5/11/6/9/12/18/24/36/48/54Mbps for you to select. Wh

Authentication Mode Open System – No authentication is needed for connecting to the AP. Shared Key – Only wireless adapters using a shared key (W

Parameter Description Filter Type Disable – Disable the MAC Address filter function. Accept – Only the wireless adapters with the MAC Address setu

4 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the adapter. 1. What

5. What is Infrastructure？ An integrated wireless and wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicab

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital

12. What is DSSS？What is FHSS？And what are their differences？ Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier that changes fr

Federal Communications Commission (FCC) RF Exposure Requirements SAR compliance has been established in the laptop computer(s) configurations wit

CONTENTS 1 INTRODUCTION... 6 1.1 Features 6 1.2 Specifications 6 1.3 Pack

1 Introduction Thank you for purchasing the Hawking Hi-Gain 6dBi Directional USB Wireless-G Network Adapter. This Hi-Gain Wireless-G USB Adapter is

• Data Rate: 54/48/36/24/18/12/11/9/6/5.5/2/1Mbps auto fallback • Security: 64/128/256-bit WEP Data Encryption, WPA (IEEE 802.1x with TKIP) and AES

2 Installation Procedure Before you proceed with the installation, please notice following descriptions. Note1: Please do not install the USB adapt

B. If you want to install the software program in another location, click “Browser” and select an alternative destination. Then, click “Next”.